If you don’t want motor noise look for the electronic latching versions from Yale and Schlage like the Schlage FE599, they’re very silent. I can say that deadbolt versions will have motor noise (Yale less the Schlage). You can check out the Yale and Schlage brands. Without keypads in the US your best bet would be the August but you’ve ruled that out. You could try rekeying it through a locksmith and see if they do it for different brands. You need a SmartApp like Lock User Management (LUM), Rental Lock Automater (RLA) or SmartLocks to program user codes, create actions fo…Īs far as keeping your existing key, that’s going to be an issue with any brand as they prefer their own keys. If a feature is not supported by the lock it will not show up or say Unsupported. It discovers/learns the lock features and automatically configures them. This works with all ZWave locks and newer ZWave Plus locks (see below for a list of locks tested). This device handler is enhanced to fix bugs in the stock ST ZWave Lock Device Handler, include patches for bugs in lock firmwares and bring out additional features for Schalge, Yale, Kwikset, IDLock, Popp, Samsung, Delaney, August Pro, Danalock, KeyWe, Philia, Vivint, Locstar etc zwave locks (see below for a full list of models and features). Test the code: While your door is open, lock it and enter the User Code to make sure it no longer unlocks the door.For all programming sequences, success is indicated when the Kwikset button flashes green 2 times and you hear 2 beeps.If unsuccessful, the Kwikset button will flash red 3 times and you will hear 3 beeps.Note: If the lock is muted, you will not hear the lock beeping.Universal Enhanced Z-Wave Lock Device Handler for Schlage, Yale, Kwikset, IDLock, Popp, Danalock, August Pro, Keywe, Philia, Samsung Community Created Device Types A “future proof” Universal Enhanced Z-Wave Lock device handler Enter the User Code you wish to delete.4. Press ""Kwikset"" then ""2"" then ""Kwikset""3. It is recommended that you delete this code.Make sure your door is open and unlocked1. Test the code: While your door is open, lock it and enter your new User Code to make sure it unlocks the door.For all programming sequences, success is indicated when the Kwikset button flashes green 2 times and you hear 2 beeps.If unsuccessful, the Kwikset button will flash red 3 times and you will hear 3 beeps.Note: If the lock is muted, you will not hear the lock beeping.Delete User Codes:The lock is pre-programmed with a default User Code of 1-2-3-4. Press ""Kwikset"" then ""1"" then ""Kwikset""3. Do not program a User Code that is the same as your PC (Programming Code).Make sure your door is open and unlocked1. How do I add/delete a user code on my 264 Deadbolt?Īdd User Codes: A total of 6 User Codes (and a temporary one-time User Code) may be programmed. Repeat steps 1 and 2 to enable or disable the codes again.For all programming sequences, success is indicated when the Kwikset button flashes green 2 times and you hear 2 beeps.If unsuccessful, the Kwikset button will flash red 3 times and you will hear 3 beeps.Note: If the lock is muted, you will not hear the lock beeping Press "Kwikset" then "8" then "Kwikset"3. Enter your existing PC (Programming Code).2. Press "Kwikset"For all programming sequences, success is indicated when the Kwikset button flashes green 2 times and you hear 2 beeps.If unsuccessful, the Kwikset button will flash red 3 times and you will hear 3 beeps.Note: If the lock is muted, you will not hear the lock beepingIf User Codes are disabled (example: when you go on vacation), the lock can only be operated by the key and turnpiece until they are enabled again.Make sure your door is open and unlocked1. Press "Kwikset" then "9" then "Kwikset"3. Make sure your door is open and unlocked1. How do I add/delete a one-time User Code on my 264 Deadbolt?Ī one-time user code may be used only once, and then it will be deleted immediately after use.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |